our services
D&E HEATING and AIR CONDITIONING offers full service for all heating and cooling systems. Our knowledgeable technicians take time with customers to explain the nature of problems and what’s needed for customers to make the best choice for repairs or the replacement of equipment.
Heater Repair
We offer an expert range of furnace & boiler heating system repair options from our trained and certified NATE technicians.
Fan Motor Replacement
Need a fan replacement? We stock the best replacement motors for all air conditioners. Call us today to get your system running fast and efficiently.
A/C Repair
We offer service for air conditioning repair options from our trained and certified NATE technicians. Call us today for a free estimate.
New System Installation
Ready to replace your Furnace, Air Conditioner or Geothermal? New systems are more energy efficient and can save you money in the long run on your energy bills. We also offer the best warranty's in the industry and FREE estimates.
​
​
(Follow the link above for more information on Geothermal)
Heat Pump Repair
General wear and tear can cause your heat pump to stop working efficiently. We pride ourselves on providing the highest level of quality and service whenever we are called to the rescue!
System Inspection &
Maintenance
We provide commercial and residential system inspections and maintenances.
We understand the importance of equipment that runs optimally and reliably, so we take our work very seriously.
Inspections
&
Maintenances
Furnace
Inspection
-
Check system control for accurate temperature rise and airflow.
-
Inspect burner operation and ignition.
-
Inspect combustion air.
-
Test system safeguards.
-
Check the gas line for leaks from the furnace shut-off valve to the burners.
-
Clean and adjust the pilot as necessary.
-
Inspect the flue for obstructions.
-
Tighten all electrical connections.
-
Inspect the blower wheel for oil leakage and debris.
-
Check amp draw on blower and furnace.
-
Check the inducer for leaking and noise.
-
Inspect the flame rod and igniter.
-
Inspect motors.
-
Check the heat exchanger and secondary collection plate.
-
Inspect CO, CO2, and flue temp.
-
Inspect the air filter and change it if provided (inform the property owner if they need a new one).
-
Clean and refill the condensate trap.
-
Wipe down the cabinet inside and out.
Maintenance
-
Everything mentioned above.
-
Clean blower components if needed.
-
Clean/vacuum secondary heat exchangers if needed.
-
Clean burners if needed.
-
Wipe down the cabinet inside and out.
Parts & New Filters Are Not Included.
ASHP / Mini-split & AC
Inspection
-
Check all electrical connections and tighten the contactor if needed.
-
Check the mf rating on the run capacitor.
-
Inspect and clean (if applicable) the air filter and change it if provided (inform the property owner if they need a new one).
-
Inspect the condensate drain and clean it if necessary.
-
Inspect the blower wheel.
-
Inspect belt.
-
Inspect the condensate safety switch.
-
Check controls of the system.
-
Inspect and spray off the outdoor condenser coil if needed.
-
Inspect evaporator coils and add drain tablets.
-
Check AC and Heat Pump operation (If not performing correctly, we will discuss repair options).
-
Wipe down the cabinet inside and out.
Maintenance
-
Everything mentioned above.
-
Chemically clean and adjust blower components if needed.
-
Chemically clean condenser and evaporator coils if needed.
-
Wipe down the cabinet inside and out.
Parts & New Filters Are Not Included.
Boiler
Inspection
-
Inspect all piping near the boiler, along with gas and vent piping.
-
Test system safeguards.
-
Verify safe settings on the boiler or anti-scald valve.
-
Verify programmed temperature settings.
-
Inspect antifreeze level.
-
Check all wire connections.
-
Check the flame signal.
-
Inspect CO, CO2, and flue temp.
-
Clean and refill the condensate trap.
-
Wipe down the cabinet inside and out.
Maintenance
-
Everything mentioned above.
-
Check burner tube and combustion chamber coils, clean when necessary, and vacuum the combustion chamber.
-
Clean the spark electrode and reset the gap.
-
Wipe down the cabinet inside and out.
Additional Chemicals & Parts Are Not Included.
Geothermal
Inspection
-
Inspect and clean (if applicable) the air filter and change it if provided (inform the property owner if they need a new one).
-
Inspect the system for leaks, loop field pressure, and corrosion.
-
Inspect the drain pan and add drain tablets.
-
Check the antifreeze level.
-
Repressurize the loop field if needed.
-
Inspect loop field temp, flow rate, and pressure drop.
-
Inspect the coil.
-
Check volts, amp draw, contactor condition, and run capacitor.
-
Wipe down the cabinet inside and out.
Maintenance
-
Everything mentioned above.
-
Chemically clean the drain pan if needed.
-
Chemically clean the coil if needed.
-
Back flush open loop system if applicable.
-
Wipe down the cabinet inside and out.